MITEQ is a recognized leader in the advanced development of RF and microwave products, multifunction assemblies and Satellite Communication Systems for both military and commercial applications. The following new products are a result of our ongoing innovative engineering and design efforts. MITEQs newest literature is available here.
|
Solid State Power Amplifier Drivers - Linear SSPA Drivers:
This new line of linear SSPA drivers, consists of three models covering all of the common satellite communication bands, AMFLD-05700850-60-16P for C-/X-Band, AMFLD-12501850-60-18P for Ku-/DBS-Band, and AMFLD-27003100-60-12P for Ka-Band. All three models have a common outline of 3.7” x 2.5” x 0.73”, SMA connectors for RF I/O and a multi-pin connector for supply, controls and detector output.
The linear drivers have a typical gain of 25 dB flat to within 1 dB, P1dB of 16 dBm and output IP3 of 26 dBm. Power monitor DC output and gain are well compensated, allowing for a compliant temperature range of –25 to +80 Degrees. Also incorporated is 30 dB of linear gain control. Drivers have a noise figure of less than 6dB, operate from a single 15V supply and draw 400 mA typical.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
New Series
 February 2008 |
|
High Power Amplifier
Model AMF-5B-09001050-40-39P provides 7 Watts of X-band power. and a has an output P1dB of about 39 dBm from 9 to10.5 GHz and 38 dBm from 7.5 to 11 GHz. Gain is 36 dB minimum, ± 1 dB flat, and typical noise figure is 3.5 dB. This model operates from -10 to +60 ° C base temperature range and draws about 4A from 15 V. It has internal regulation and protection, and a footprint of only 3.3 inch x 3.3 inch. Unit is available as RoHS compliant, please contact MITEQ.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
 |
|
Broadband Power Amplifier
Model AMF-2B-00030300-150-32P is a 2W amplifier, offering 20 dB of gain from 30 MHz to 3 GHz. The 24V voltage required is also internally gated by the external -5V to minimize any chance of damage. Very compact, 2 inch by 2 inch by 0.5 inch, housing has two SMA connectors and can be bolted on a heat sink. It draws 600 mA maximum and has a typical noise figure of about 8 dB and an input match of 1.5:1 maximum. Unit is available as RoHS compliant, please contact MITEQ.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
 |
|
26-31 GHz 5W Power Amplifier
Model AMF-4B-26003100-100-36P is a connectorized high-power amplifier/module, covering 26-31 GHz and delivering approximately 5W of power. The Female K-type connectorized aluminum housing is 10mm (H) x 25mm (L) x 34mm (W). It is intended for bolting to a flat cooling surface or fins. Housing is environmentally sealed and EMI shielded. Hermetic sealing option is also available. Nominal small-signal gain is near 18 dB. Current draw is nominally 7A at P1dB from 6-6.5 VDC of supply and -1.25 VDC. Unit is available as RoHS compliant, please contact MITEQ.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
 |
|
43.5-45.5 GHz Waveguide Amplifier
Model AMFWW-10F-43504550-50-25P has 35 dB minimum gain over the full band, with a minimum P1dB of 25 dBm. Typical noise figure is 5 dB. UG383/U waveguide input and output ports have a low VSWR of 1.5:1. It typically draws 1A from a 15V supply. Picture shown does not include isolators.
This amplifier has built in regulation, reverse bias protection and TTL control is optional. It includes a custom heat sink that can be removed. Other models from 15 dBm to 30 dBm are also available. Unit is available as RoHS compliant, please contact MITEQ.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
 |
|
Q-Band Waveguide Limiter LNA
Model AMFW-5F-033004000-50-10P-4WL is a very low noise Q-Band waveguide front end. WR-28 waveguide input and output amplifier is very lightweight and has an extremely small profile and footprint. Aluminum alloy housing is environmentally sealed and EMI shielded. Hermetic sealing option is also available. LNA includes reverse voltage, over current and over temperature protection, in addition to full internal regulation.
This amplifier is capable of a minimum of 10 dBm of P1dB across the full band, 33-40 GHz. Built-in limiter can prevent damage from up to 5W of CW input. Port VSWR is a maximum of 2.5:1 but typically 2:1 or less. Nominal small-signal gain is minimum 18 dB and maximum of 22 dB while the noise figure is less than 5 dB. Gain flatness is 2 dB peak-to-peak typical. Current draw is nominally 165 mA from a single positive 15V supply. Unit is available as RoHS compliant, please contact MITEQ.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
 |
|
8-18 GHz Broadband High Power Amplifier
Model AMF-2B-08001800-65-35P is a connectorized high power amplifier, covering octave bandwidth from 8-18 GHz and delivering approximately 3W of power and 2.5W from 6-18 GHz. In the band of 10-15 GHz, it delivers about 7W of P1dB. The SMA connectorized aluminum housing is 21mm (H) x 95mm (L) x 66mm (W). It is intended for bolting to a flat cooling surface or fins. Housing is environmentally sealed, EMI shielded and hermetic sealing option is also available. Power Amplifier includes reverse voltage protection, in addition to full internal regulation. A TTL-control pin is optional.
Nominal small-signal gain is 50 dB while noise figure is better than 5 dB across the band. Current draw is nominally 6.2A at P1dB from 12 to 15 VDC of supply. Output IP3 is a minimum of 44 dBm across the full band, closer to 47 dBm from 10–15 GHz. Unit is available as RoHS compliant, please contact MITEQ.
Related Products... Components: Amplifiers Search For Additional Amplifiers |
 |
|
New 90 Degree Hybrid Couplers |
90 Degree Hybrid Coupler
MITEQ's model: M-23-183-91WS, is a 2 to 18 GHz, 90 degree hybrid coupler. This unit is connectorized with SMA female connectors and has a phase balance of <+/-10 degrees and amplitude balance of <1.5 dB. This unit measures 1.91” x 1.11” x .44” . This model is also available as RoHS compliant, MITEQ model: M-23-183-91WS-R.
Contact MITEQ.
Related Products... Components: 90 And 180 Degree Hybrid Couplers
Search For Additional 90 And 180 Degree Hybrid Couplers
|
 |
|
New Integrated RF and Microwave Assemblies |
Low-Noise, High Dynamic Block Downconverter
Model LNB4044N01T is part of a line of low-noise (less than 3.3 dB), high dynamic block downconverters. The LNB4044N01T incorporates a fixed frequency phase-locked LO to convert the 40 to 44 GHz RF to a 1 to 5 GHz IF band. These converters are packaged in a 5" x 5" ruggedized aluminum housing with flange mount and integrated waveguide input.
Contact MITEQ.
Related Products... Components: Integrated RF and Microwave Assemblies
Search For Additional Integrated RF and Microwave Assemblies
|
 |
|
|
TTL Controlled Millimeter-Wave Quad-Phase Modulator
Now available from MITEQ, a 2-bit TTL controlled Millimeter-Wave Quad-Phase Modulator with an operational frequency range of 26-40 GHz and modulation rates from DC to 40 MHz. The Model SMT2640LC15MDQ has a typical phase balance of <+/-15 degrees and an amplitude balance of <+/-2.5 dB.
Contact MITEQ.
Related Products... Components: Modulator Products
Search For Additional Modulators |
 |
|
|
X6 Multiplier
MITEQ introduces two more models into their multiplier family of products. Model SYS6X0639 is an X6 multiplier that accepts inputs from 6.375 to 6.566 MHz at 10 dBm and produces outputs from 38.250 to 39.400 MHz at 5 dBm. Input harmonic rejection is –70 dBc minimum and the unit includes integrated printed filters. The SYS6X0639 measures 1.280” x 1.200” x 0.275”.
Frequency Quadrupler
Model SYS4X0520 is a frequency quadrupler that produces a 20 GHz, 10 dBm signal for an input of 12 dBm at 5 GHz. This multiplier also features high rejection to input harmonics by using printed ceramic filters to achieve –80 dBc or better suppression of odd harmonics and –70 dBc or better for even harmonics. The SYS4X0520 measures 1.280” x 1.200” x 0.270” without connectors. Both multipliers are supplied with field replaceable SMA female input and male output K-connectors, require +15V at 130 mA, -15V at 10 mA and are supplied in hermetic housings.
Contact MITEQ.
Related Products... Components: Multiplier Products
Search For Additional Multipliers
|
 |
|
New Power Divider/Combiners |
2-Way Power Divider
MITEQ’s new 2-Way Power Divider Model PD2-1030-250N operates in the frequency range of 1,020 to 1,040 MHz and is able to handle up to 250 watts average power. This device is available with N-Type connectors and has an isolation of 25 dB, insertion loss of 0.5 dB, amplitude balance of ±0.1 dB and phase balance of ±1 degree. This model is also available as RoHS compliant, MITEQ model: PD2-1030-250N-R.
Contact MITEQ.
Related Products... Components: Power Dividers/Combiners
Search For Additional
Power Dividers/Combiners |
 |
|
|
Miniature Digital Five Throw Switch - SP5T Switch
MITEQ would like to introduce its’ new absorptive Single Pole Five Throw Switch, Model SW5-005180AI3NF-S0001. It covers the frequency range from 500 MHz to 18 GHz with a minimum of 60 dB isolation and VSWR of 2:1 maximum. The 4 BIT input control word is TTL compatible and commands switching time from 50% control input to the 10% to 90% settling within 100 ns. Rise/Fall time is <20 ns typical. The power handling capability is 20 dBm. This model measures 1.7” across (including connectors) and is 0.37” thick. Weighs 19 grams.
Related Products... Components: PIN Diode Switches, Search For PIN Diode Switches |
New Product 
April 2008 |
|
Digital Single Pole Two Throw Switch - SP2T Switch
MITEQ introduces an absorptive Single Pole Two Throw Switch, Model SW2-005180RN3NF, covering the frequency range from 500 MHz to 18 GHz with a minimum of 60 dB isolation from .5 to 12 GHz and 55 dB isolation from 12 to 18 GHz and VSWR of 1.8:1 maximum. The 2 Bit input control word is TTL compatible and commands switching from 50% control input to the 10 to 90% settling within 40 nS. The power handling is 20 dBm. Rise/Fall time is <20 ns typical. Options available include extended band and sub-band versions.
Related Products... Components: PIN Diode Switches, Search For PIN Diode Switches |
New Product 
March 2008 |
|
Digital Single Pole Two Throw Switch - SP2T Switch
MITEQ introduces an absorptive Single Pole Two Throw Switch, Model SW2-200305RD2NF, covering the frequency range from 20 to 30.5 GHz with a minimum of 30 dB isolation and VSWR of 2:1 maximum. The 1 Bit input control word is TTL compatible and commands switching time from 50% control input to the 10 to 90% settling within 30 nS. Rise/Fall time <20 ns typical. The power handling is 20 dBm. Options available include an extended band and sub-band version.
Related Products... Components: PIN Diode Switches, Search For PIN Diode Switches |
New Product
March 2008 |
|
Digital Single Pole Three Throw Switch - SP3T Switch
MITEQ introduces a reflective Single Pole Three Throw Switch, Model SW3-005205RI1NF, covering the frequency range from 500 MHz to 20.5 GHz with a minimum of 60 dB isolation and VSWR of 1.8:1. The 3 Bit input control word is TTL compatible and commands switching time from 50% control input to the 10 to 90% settling within 180 nS. The Rise/Fall time is <20 ns typical. The power handling is 20 dBm.
Related Products... Components: PIN Diode Switches, Search For PIN Diode Switches |
New Product 
March 2008 |
|
Digital Single Pole FourThrow Switch - SP4T Switch
MITEQ introduces an absorptive Single Pole Four Throw Switch, Model SW4-001145AI3NF, covering the frequency range from 70 MHz to 14.5 GHz with a minimum of 80 dB isolation and VSWR of 2:1 maximum. The 4 BIT input control word is TTL compatible and commands switching time from 50% control input to the 10% to 90% settling within 1uS. The power handling is 20 dBm. Options available include extended band and sub-band versions covering the entire 70 MHz to 18 GHz range.
Related Products... Components: PIN Diode Switches, Search For PIN Diode Switches |
New Product 
January 2008 |
|
Digital Single Pole Ten Throw Switch - SP10T Switch
MITEQ introduces an absorptive Single Pole Ten Throw Switch, Model SW10-001145AN3NF, covering the frequency range from 70 MHz to 14.5 GHz with a minimum of 80 dB isolation and VSWR of 2:1 maximum. The 10 BIT input control word is TTL compatible and commands switching time from 50% to 90% settling with 2 uS. The power handling is 20 dBm. Options available include extended band and sub-band versions covering the entire 70 MHz to 18 GHz range.
Related Products... Components: PIN Diode Switches, Search For PIN Diode Switches |
New Product 
January 2008 |
|
|
MOS Series - Frequency Synthesizers
MITEQ would like to introduce its’ MOS Series of multi-octave wide, low phase noise synthesizers which offer an economical solution for lab and communication test applications. Band coverage is from 100 MHz to 20 GHz. The MOS Series has a standard 1 kHz step size, with optional full-band fast switching available. The field-tested design and low power dissipation proves to demonstrate higher MTBF and higher reliability. These synthesizers are available in either one third-rack mounted chassis with front panel control, or a modular 5” x 8” x 1.25” package with either serial or parallel control.
Related Products... Components: Synthesizers, Search For Synthesizers |
New MOS Series 
April 2008 |
|
UWB Series - Frequency Synthesizers
MITEQ would like to introduce its’ new UWB (Ultra Wideband) Series of frequency synthesizers. These units are designed as an ideal replacement for any type of YIG based synthesizer. The UWB Series can lower the system power dissipation, and reduce micro-phonic sensitivity that are characteristic of the older YIG based type synthesizer. This series is available in the 4.5 to 13 GHz frequency range and is ideal for ELINT, test translation and instrumentation applications. Ultra-wide bandwidth, fast switching, and low power consumption makes this series an ideal alternate for those YIG based synthesizers. The UWB is available in step sizes down to 1 kHz, and has an output power of +13 dBm minimum.
Related Products... Components: Synthesizers, Search For Synthesizers |
New UWB Series 
April 2008 |
|
BTE Series - Frequency Synthesizers
MITEQ introduces the BTE Synthesizer Series which are designed to meet the most demanding phase noise requirements. The BTE Series can meet the most stringent phase noise requirements from S- through Ku-Band. The BTE Ku-Band noise performance is over 20 dB below Intelsat IESS 308/309 with over 2 GHz of tuning bandwidth and 1 kHz step size. This series is also available with a fixed second LO output option which also maintains the low noise of the main output in dual conversion systems. Fixed LO can be tuned to alternate frequency via communication interface. The BTE is packaged to meet extremely low EMI emission requirements and has options for parallel or serial communications and control.
Related Products... Components: Synthesizers, Search For Synthesizers |
New BTE Series 
Febuary 2008 |
|
SLFS Series - Frequency Synthesizers
MITEQ introduces the SLFS Synthesizer Series that offers a compact and economical solution for SATCOM and VHF Ku-Band microwave communication systems. The SLFS can be controlled with any notebook or desktop PC with a user friendly Graphic User Interface available as a download from the MITEQ website. This series is available in VHF through Ku-Band with typical bandwidths of 800 MHz, with an efficient design that dissipates only 2.5 Watts. The SLFS is available in wider bandwidths and custom step sizes as required.
Package size is modular, 2.25” x 2.25” x 0.6”, SMA input and output with 7 PIN JST interface connector.
Related Products... Components: Synthesizers, Search For Synthesizers |
New SLFS Series 
Febuary 2008 |
|
|
Beacon Receiver
MITEQ’s BR Series Beacon
Receiver is a versatile receiver designed to lock onto a CW or modulated
carrier and provide accurate and reliable relative power measurement indicators
for either antenna positioning or uplink power control applications.
The BR-L operates in the
L-Band and accepts a 940-2150 MHz signal. The outputs of the beacon receiver are analog and digital indicators of
power measured at the input of the beacon receiver. The beacon receiver fits neatly into a single EIA standard
rack height (1.75 inches).
The rich feature set of
controls and indicators are easily accessible via in intuitive operating
environment. The receiver can be
setup completely from the front panel or over a remote bus via a host computer. There are 32 memory locations where
various setups can be stored and recalled easily. Also, a log is continuously updated with time-stamped
records of alarm activity.
Related Products... SATCOM: Uplink Power Control Products |
New Product
April 2008 |
|
Broadband CW TWT Lab Amplifier
MITEQ introduces the new Broadband CW TWT Lab Amplifier . This broadband CW TWT lab amplifier is the ideal high power amplifier for EMI/EMC testing. It has been expanded and now covers the following bands with output powers of: 2.5 – 7.5 GHz at 550W typical, 2.0 – 8.0 GHz at 400W typical, 6.0 – 18.0 GHz at 325W typical, 7.5 – 18.0 GHz at 325W typical, 18.0 – 26.5 GHz 75W typical, 26.5 – 40.0 GHz 35W typical. The MT4100 broadband amplifier is leveraged around the field-proven MT4000 TWT architecture. With its modular design, compact and efficient packaging, the MT4100 will exhibit unsurpassed reliability.
Related Products... SATCOM: High Power Instrumentation Amplifiers |
New Product
January 2008 |
|
9800 Series Frequency Converters
MITEQ introduces the 9800 Series to their Frequency Converters product line. This Series is designed for advanced satellite communication systems and are available for a wide variety of frequency plans. Phase noise, amplitude flatness and spurious outputs have been optimized to provide the user with a transparent frequency conversion for all video and data applications. A strong feature set of monitor and control functions supports powerful local and remote control. Among the features are control of frequency, attenuation and 64 memory locations for each converter where various setups can be stored and recalled.
Contact MITEQ.
Related Products... SATCOM: Converters |
New Product November 2007 |
|
Uplink Power Control System
The MITEQ Uplink Power Control Unit product line now expands to include the UPC-L version. The UPC-L offers the Earth station operator/designer control of the full L-band bandwidth of 950-2150 MHz. The UPC-L RF Signal path utilizes internal bias tees and diplexers on the center conductor to provide both DC and 10 MHz through path in the attenuator. This allows the user to pass the 10 MHz reference signal and DC bias from a modem through the UPC-L out to a block upconverter.
These units can be delivered within 45 days, in small quantities.
Contact MITEQ.
Related Products... SATCOM: Uplink Power Control Units
|
New Product November 2007
|
|
Switchable Band Test Loop Translator
MITEQ introduces the new Switchable Band Test Loop Translator product line. These units are designed to translate the C-, X- and Ku-Band transmit bands to their respective receive frequency bands. The units feature minimum amplitude and delay distortion, high frequency stability, low intermodulation and phase noise contribution. The units are available with 10/100 Base-T Ethernet and RS485/422 remote interfaces. This unit series replaces the 8600 series of Switchable Band Test Loop Translators.
Contact MITEQ.
Related Products... SATCOM: Translators
|
New Product November 2007
|
|
9900 Series Frequency Converters
MITEQ’s 9900 Series communications up and downconverters are offered in extended C- and Ku-band. The C-band models cover 5.725-6.725 and 3.4-4.2 GHz, while the Ku-band models cover 13.75-14.8 and 10.7-12.75 GHz. Phase noise, amplitude and spurious performance has been optimized to provide a transparent frequency conversion for all video and data applications. Ethernet remote capability is available as an option.
Contact MITEQ.
Related Products... SATCOM: Converters
|
 |
|
|
 |
|
MT7100 Dual-Drawer TWTA
MCL introduces the MT7100 Traveling Wave Tube Amplifier consisting of two drawers – an RF drawer and a power supply drawer that are designed to fit into a standard 19” wide cabinet. This TWTA is available for C- and X-Band applications from 2.2 to 2.5kW, as well as Dual-Band (C/X) applications. Some features include an event log screen, continuous attenuator adjustment in dB, and an internal control bus consisting of high priority parallel signals and lower priority serial (RS485) bus communications. This unit can also be customized to include such options as manual override, manual attenuator, internal linearizer or block upconverter with L-Band input. Redundancy can be achieved through 1:1; 1:2 or phase combined systems.
Contact MITEQ.
Related Products... SATCOM: TWT Power Amplifier Products
|
 |
|
| |
